If a rear spring has snapped or the car sits low on one corner, the right move is to replace both rear suspension coil springs as a matched pair and to match the original free length, wire diameter and spring rate instead of fitting whatever happens to be in stock. A single mismatched spring changes rear roll stiffness and ride height from side to side, which shows up later as uneven tyre loading, vague steering and premature damper wear. What follows explains what a rear coil spring actually does, how it fails, and which specifications decide whether a replacement behaves like the factory part.
What Rear Suspension Coil Springs Actually Do
A rear coil spring does three jobs at once: it carries the rear corner weight of the vehicle, it allows the wheel to rise and fall over bumps without passing every impact straight into the body, and it fixes the static ride height that the rear alignment angles and damper travel were designed around. It is a structural component, not a comfort extra.
Most of that behaviour is described by a handful of measurable figures, and they interact. Change one and the others shift with it.
- Spring rate in N/mm (or lb/in) is the force needed to compress the spring by one millimetre. It determines how firmly the rear resists roll, payload and mid-corner load transfer.
- Free length is the unloaded length. It sets the ride height once the spring is seated and the car is on its wheels.
- Load at design height is the actual force the spring carries at kerb weight — the number that tells you whether the car will still sit level with a full boot.
- Wire diameter and coil count control stress levels. A thinner wire of the same rate runs at higher stress and fatigues sooner.
Rear springs are also built differently from front ones. Because the rear axle usually carries payload, many rear springs are progressive or variable rate, with a softer initial section for solo driving and a stiffer final section for load. Side-load, or "banana", rear springs are wound with an offset axis so the spring pushes back against the damper's side load, cutting friction in the strut and improving small-bump comfort. Neither feature can be judged by eye, which is why specification sheets matter more than appearance.
How Rear Coil Springs Fail, and What You Notice First
Rear coil springs almost never fail without warning: they sag gradually, then corrode, then snap at the lowest coil, and the car gives several clues along the way. Recognising them early avoids driving on a broken coil that can puncture a tyre or damage the spring seat.
- One rear corner sits 10 mm or more lower than the other when measured from wheel arch to wheel centre on level ground.
- The rear bottoms out on speed bumps with two passengers, or scrapes on driveways it used to clear.
- A metallic clunk or twang over sharp bumps, often caused by a broken coil end rotating in its seat.
- Heavy rust, flaking coating or bright metal exposed on the lower coils, where road salt collects.
- Uneven or feathered wear on the rear tyres, or a steering wheel that no longer centres cleanly.
- A broken pigtail discovered during tyre, brake or MOT work rather than felt by the driver.
Coating damage is often the real starting point. Once moisture reaches bare steel, corrosion pits the wire surface and fatigue cracks initiate from those pits. A field guide to the sequence is covered in five warning signs of suspension spring fatigue, which is worth reading before ordering parts.
The Specifications That Must Match When You Buy
The three figures that decide fit and behaviour are wire diameter, free length and rate, and they should be taken from the vehicle's specification or from a measured, un-sagged sample — never guessed from a photo. A spring can look identical and still be 15% off rate.
| Specification | What it controls | Practical check |
|---|---|---|
| Wire diameter | Load capacity and working stress | Measure with a calliper; a 0.2 mm difference is meaningful |
| Free length | Static ride height before load | Only compare with the old spring if it has not sagged |
| Spring rate | Roll stiffness and payload behaviour | Confirm N/mm or lb/in, and whether the rate is linear or progressive |
| End form and winding | Seating in the lower arm or strut cup | Check pigtail type, coil count and winding direction |
| Finish and corrosion life | Service life in salt and grit | Ask for a salt-spray report alongside the coating type |
| Load-deflection curve | Support at the designed ride height | Request the curve, not a single load figure |
Tolerances matter more than they look. A spring that is 8% stiffer than original on one side only will bias the rear roll stiffness, which the driver feels as a car that turns in differently to the left and right. Reputable suppliers quote rate tolerance per batch, typically within a few percent, and test every batch rather than sampling once a year.
Standard, Heavy-Duty or Lowered: Choosing the Right Rear Spring
Choose the variant that matches how the car is actually used, not the stiffest option available, because every increase in rate is paid for in ride comfort and damper matching. Standard replacement suits most drivers; heavy-duty suits towing and constant loads; lowered springs suit drivers chasing body control and stance.
| Variant | Rate versus original | Best suited to |
|---|---|---|
| Standard OE replacement | Within roughly ±5% | Restoring factory ride height, comfort and handling balance |
| Heavy-duty / load-carrying | Around 10–25% higher, often progressive | Towing, frequent full loads, taxis and light commercial use |
| Lowered / modified | Higher rate with 20–50 mm shorter free length | Reducing body roll, closing arch gaps, track-day use |
For a daily driver returning to factory behaviour, an OE-type rear spring is usually the correct answer, and pairing it with fresh insulators and dampers restores the ride the car was signed off with.
OE Replacement Car Suspension Springs ManufacturersOE replacement car suspension springs are aftermarket coil springs manufactured to match the dimensional, load, and performance specifications of the Original Equipmen...View Product →
When a Modified Rear Spring Makes Sense
A modified rear spring is the right choice only when the rest of the system is prepared for it: shorter dampers or matching valving, corrected bump stops, and an alignment afterwards. Fitting a lowered spring onto standard-length dampers costs travel, and the car will spend its time on the bump stops on poor roads — stiffer, but not faster or more comfortable.
Modified Car Suspension Spring RangeBrowse modified suspension springs for off-road and road cars, including lift, progressive, heavy-load and lowering types; use to plan a complete assembly.View Product →Fitting: What Else Wears Out Alongside the Spring
Replacing the spring alone rarely restores the original behaviour, because the parts around it age at the same rate and are far cheaper to change while the strut is already apart. Budget for the whole assembly the first time.
- Upper and lower spring insulators, which harden and crack and allow metal-to-metal contact.
- Strut mounts and bearings at the rear, which cause clunks that are often blamed on the spring.
- Bump stops and dust boots, which crumble and let grit reach the damper rod.
- Dampers, which lose damping gradually and cannot control a new, correctly rated spring if worn.
- Mounting bolts and nuts specified as single-use items in the workshop manual.
After fitting, measure ride height on level ground with the car at kerb weight and the tank at a comparable level, then have the rear alignment checked. A spring change alters camber and toe on most independent rear suspensions, and the difference is enough to wear a tyre edge over a season.
What to Check in a Supplier Before You Buy
The reliable signals of spring quality are process control and test data, not marketing language — ask for the heat treatment, shot peening and load-test records for the batch you are buying. These steps decide fatigue life far more than the steel grade alone.
A credible rear spring has been coiled to length, heat treated to a controlled hardness, shot peened to put the wire surface into compression, set or scragged to remove the initial loss of height, and then coated. Each step addresses a specific failure mode: poor heat treatment softens the wire, missing shot peening leaves surface cracks free to grow, and skipped setting lets the spring settle 5–10 mm in the first months on the car. Suppliers working to IATF 16949 with in-house fatigue and load-deflection testing can usually show a curve per batch. Our coil spring product range is built on exactly that sequence, with dimensional and load checks recorded batch by batch.
Frequently Asked Questions
How long do rear suspension coil springs last?
Typically 100,000 to 150,000 km, but corrosion and road salt shorten that considerably. Springs in coastal or heavily salted regions often need replacing at half that distance, even when the car has covered low mileage.
Can I replace just one rear spring?
Only in an emergency. Rate and free length vary slightly between batches, and mixing an old and a new spring leaves the rear axle unbalanced. Replace both springs on the same axle together.
Do rear springs affect wheel alignment?
Yes. Ride height directly changes camber and toe on independent rear suspensions, which is why an alignment check after fitting is part of the job rather than an optional extra.
Are stiffer rear springs better for towing?
Up to a point. A 10–25% higher rate with a progressive final section helps keep the rear level under load, but going beyond that without matching dampers simply transfers load into the mounts and reduces grip on uneven surfaces.
Why does my car sit lower on one rear corner?
Usually a sagging or broken spring, but a collapsed insulator, a bent lower arm or a seized damper can produce the same symptom. Measure both sides at kerb weight before assuming the spring is at fault.
Rear suspension coil springs reward accurate specification more than any other chassis part discussed at the counter. Get the rate, free length and wire diameter right, replace them as a pair, refresh the mounts and dampers while the struts are apart, and the rear of the car returns to the behaviour it was engineered for.